IEC 60268 7 PDF

IEC SOUND SYSTEM EQUIPMENT –- PART 7: HEADPHONES AND EARPHONES. Buy IEC SOUND SYSTEM EQUIPMENT – PART 7: HEADPHONES AND EARPHONES from SAI Global. IEC Ed. Sound system equipment – Part 7: Headphones and earphones IEC (E), is applicable to headphones, headsets, earphones.

Author: Zulugore Nekree
Country: Spain
Language: English (Spanish)
Genre: Literature
Published (Last): 18 August 2007
Pages: 333
PDF File Size: 12.88 Mb
ePub File Size: 8.14 Mb
ISBN: 228-2-34358-336-4
Downloads: 42530
Price: Free* [*Free Regsitration Required]
Uploader: Najin

FebDecember 17, – 3: You are ready to start the sequence.

A statistics step calculates the mean of the 3 unoccluded measurements. Uec the smart route to manage medical device compliance. Noise speakers are set up adjacent to the HATS left and right ears. The Hz recorded time waveforms are processed using heterodyne analysis to derive their fundamental values.

Accept and continue Learn more about the cookies we use and how to change your settings.

The folder contains dependent files required to run the sequences. Your basket is empty.

IEC | IEC Webstore

You may find similar items within these categories by selecting from the choices below:. Connect the impedance boxes between the headphone amp out and headphone input. It then enters a loop which will run 5 times. The sequence then goes through a series of acquisition steps to generate four fundamental curves which are then post-processed to calculate crosstalk. The sequence prompts the operator to enter the rated voltage and rated impedance of the DUT.

Setup System, Hardware and Calibration Before attempting to run any of the sequences, read the following setup instructions. Sound System Equipment — Part 7: It is recommended that the sequences be run directly from the IEC folder.

  RECOVERY AND REFINING OF PRECIOUS METALS BY C.W.AMMEN PDF DOWNLOAD

This value is converted to dBV and used to calculate the IM and difference frequency stimulus levels. This website is best viewed with browser version of up to Microsoft Internet Explorer 8 or Firefox 3.

Hardware Requirements In order to run the sequences, the following hardware is required: A series of post processing steps calculates the attenuation curves, their average values and shows them on the final display. If the answer is Yes, the user is prompted to turn irc ANC on and the sequence repeats the passive measurements.

Worldwide Standards We can source any standard from anywhere in the world. In order to add these Signal Paths to your System Calibration or relink to existing Signal Paths, you should open each of the sequences individually and, if prompted, add or relink Paths to your System Calibration.

The ie from each loop iteration is displayed as it is acquired. Calibrate the microphones per the instructions in the SoundCheck manual.

600268 Test Setup for measuring headphone voltage sensitivity. If the answer is No, the sequence jumps to post-processing steps which calculate passive attenuation and the final display step. Headphone Voltage Sensitivity Final Display. A series of post-processing steps follow to apply the weighting and correction curves, calculate the LAEQ and then the Simulated Program Characteristic Voltage is calculated along with the Hz voltage sensitivity.

If passive, connect to the headphone amp or separate audio power amplifier You are ready to start the sequence. The user is first prompted to enter the rated voltage.

  LTA320WT L08 PDF

IEC Headphone Sequences – Listen, Inc.

Marking, Microphones, Audio systems, Ratings, Designations, Instructions for use, Headphones, Classification systems, Frequency 60286, Earphones, Audio equipment, Voltage measurement, Impedance measurement, Testing conditions, Preamplifiers, Comparative tests, Acoustic measurement, Electrical wave measurement, Electrical properties and phenomena, Acoustic testing.

You may experience issues viewing this site in Internet Explorer 9, 10 or It can also be used to characterize the passive attenuation only of a standard non-ANC headphone. Calibrate the headphone amplifier channels per the instructions in the SoundCheck manual. Matthew Miller November 15, – 6: There are several unique Signal Paths used in the sequences which are not a part of the default SoundCheck installation. Click to learn more.

Please download Chrome or Firefox or view our browser tips.

BS EN 60268-7:2011

Crosstalk and radiation curves are then shown on the final display. No – I don’t want to receive the latest audio test information by email. Find Similar Items This 660268 falls into the following categories. The sequence uses a stepped sine stimulus to measure frequency response, THD and impedance, a 6026 signal of 70 Hz and Hz with an amplitude ratio of 4: First, a pink noise stimulus is played from the noise speakers and recorded by the unoccluded ears.

Learn more about the cookies we use and how to change your settings.