ISO and PSPC, the term used is. “nominal dry film thickness.” • For consistency in comparisons of area in this article, square meters are used to describe. STANDARD. ISO. Second edition. Reference number. ISO (E). This is a free 5 page sample. Access the full version online. ISO Paints and varnishes – Corrosion protection of steel structures by protective paint systems – Measurement of, and acceptance.
|Published (Last):||9 September 2007|
|PDF File Size:||6.93 Mb|
|ePub File Size:||12.20 Mb|
|Price:||Free* [*Free Regsitration Required]|
ISO – Free Download PDF
Calibration certificates should be accessible for review. Soiling of the painted surfaces between layers is inadmissible. For undated references, the latest edition of the referenced document including any amendments applies. Calibration is carried out by the gauge manufacturer using traceable thickness standards in most cases. For more details, see Annex C. If the acceptance criteria above are not met, the inspection area shall be rejected see also ISO series.
When, during a series of measurements, an individual dry-ilm thickness value does not meet a criterion [see 9 b and d ], a repeated measurement not more than 10 mm from the point of the irst measurement shall be carried out.
Shall be done on every parts. A4 Paint manufacturer s: In this case, the arithmetic mean value of the four readings is used in place of an individual reading.
It is good practice to identify uso areas of the structure that are affected by welding, cutting, bending and other processes which change the shape, thickness, magnetic properties due to work hardening, heat treatment, etc. Skip to main content. If this individual dry-ilm thickness 198400 not meet the criterion see Clause 9it shall not be replaced. The objective of this International Standard is to achieve uniformity of practice for measuring the dry-ilm thickness of a coating on a roughened surface.
Documents connected with procedure Dree Date of measurement: The effect of surface roughness on the measurement result increases with proile depth, but the result will also depend on the design of the measurement probe and the thickness of the coating.
Any arisen soiling should be immediately removed and damaged layer should be restored. Sio minimize measurement errors on a blast-cleaned surface, it is recommended that at least one of the shims used for adjustment be thinner than the ilm to be measured. Percentage of those rfee compared with the total number of measurements: Ideally, gauges should be adjusted using a sample of steel which is truly representative of the substrate to be tested.
They measure the magnetic ield strength produced by eddy currents caused by the probe in a conductive substrate.
The chosen methods entail the measurement of dry-ilm thickness using measurement instruments based on the permanent magnet principle and the inductive magnet principle. Classiication of environments ISOPaints and varnishes — Corrosion protection of steel structures by protective paint systems — Part 3: Should be done on every parts.
The magnetic ield strength is related to the coating thickness. Science Chemistry Materials Science Acceptance criteria: The electrical and magnetic properties of the substrate can vary depending on differences in its chemical composition and morphological structure, e.
One test on one batch should be done. Representative photographic examples of the change of appearance imparted to steel fres blast-cleaned with different abrasives ISO Blasting Blast clearing to be executed in specially equipped chamber.
The mean dry-ilm thickness es belonging to an inspection area s fre also be given. Coating procedure tests and acceptance criteria: Applied personal protection equipment The person for carrying out inspections, verification and verification of personal qualification shall be qualify in accordance NShas FROSIO certificate with inspector level 3 4.
Help Center Find new research papers in: Workplaces should be accessible for inspection of safety data sheets of applied paints by personnel. The strength of the magnetic ield is related to the coating thickness.
Acceptance criteria: ISO 19840 and coating system
At a substrate thickness of above approximately 5 mm, the effect is generally insigniicant. Calibration, on the other hand, is the process uso setting and recording the thickness values displayed fre a dry-ilm thickness gauge to known values of thickness across the range of the gauge.
ISOPaints and varnishes — Determination of ilm thickness ISOPreparation of steel substrates before application of paints and related products — Surface roughness characteristics of blast-cleaned steel substrates — Part 1: Following completion of a series of measurements, and preferably during the measurements, the adjustment of the instrument shall be re-veriied.
Technical data sheets; Safety data sheets; Coating system no. NOTE As a rule, the effect of substrate thickness is manifest in substrates up to a thickness free approximately 1 mm.
Test should be done on small part – 3 or 4 testbig part – every parts. Roughened steel substrates include those prepared by abrasive blast- cleaning or abrading. NOTE 2 For deviating surface proiles or in the case of particular agreements between the interested parties, frde method for determining the correction value to be used is given in Annex D.
It is necessary to handle painting materials very accurately, prevent their hit into the earth, reservoirs. Individual reading Correction value used Resulting individual Individual dry-film see Table 2 of dry-film thickness thicknesses outside of ISO